The update file "FRITZ.Box_7590_AX-xx.xx.image" on ftp.avm.de contains the latest FRITZ!OS (Firmware) for the FRITZ!Box 7590 AX. **Attention:** This update file is only intended for use with FRITZ!Box 7590 AX! Please follow the instructions at the end of this file to install the update. ``` Product: FRITZ!Box 7590 AX Version: FRITZ!OS 8.00 Language: Dutch, English, French, German, Italian, Polish, Spanish Release date: 16/09/2024 ``` **New features:** ------------------------------------------------------------ - User interface: Diagram showing the connections in the overview (homepage) - New Online Monitor informs about the load on the internet connection and the load by individual network devices - Internet: Now IPv6 data can also be transmitted via a WireGuardŽ VPN tunnel - Mesh: Redesigned diagram of all devices connected with the FRITZ!Box with additional functions - DECT: The number of DECT telephone calls possible concurrently was increased from three to five - Push service: Reworked design and more convenience ------------------------------------------------------------ With each FRITZ!OS update, AVM also updates its security functions. Therefore we recommend performing the update for all devices. ------------------------------------------------------------ Below you find a complete list and descriptions of the new functions in the latest FRITZ!OS, along with a list of further improvements in this version. --- # New features and improvements in FRITZ!OS 8.00 ## Internet: - **NEW** IPv6 data now can also be transferred via a WireGuardŽ VPN tunnel (new WireGuardŽ connection required, no forwarding of IPv6 data to the internet) - **NEW** New Online Monitor diagram with expanded information on the load on the internet connection by individual network devices - **NEW** Extend online time restricted through parental controls by 45 minutes directly in the detailed settings of the network device - **Improved** When sharing internet access to FRITZ!Box services, an additional IP block list from AVM can be used - **Improved** For VPN network couplings via WireGuardŽ, the "fritz.box" domain is resolved in the entire coupled network - **Improved** For VPN network couplings via WireGuardŽ, the domain of the remote site can be specified for DNS resolution - **Improved** More precise explanations of errors during the configuration of WireGuardŽ connections - **Improved** Added notification about potential risk of sharing port 80 or 443 - **Improved** Preselection of easiest configuration method for the internet providers Telekom, Vodafone, and EWE for initial configuration on a fiber optic connection - **Improved** Improved details during the initial configuration behind a fiber optic modem (ONT) - **Improved** Selection of automatically fair bandwidth distribution in the home network including Ingress shaping as own option in the prioritization settings - **Improved** The FRITZ!Box user interface can also be opened in the home network by entering "fritzbox.internal" and "fritzbox.home.arpa" ## Wi-Fi: - **NEW** Visualization of Wi-Fi usage in the home network for the last 7 days added on "Wi-Fi > Wi-Fi Channel" ## Mesh: - **NEW** Definition of a name and an icon for network devices directly in the Mesh Overview diagram (tooltip) - **Improved** Details about the LAN connections between FRITZ! devices given in the Mesh Overview diagram (tooltip) ## Telephony: - **Improved** Recordings on the answering machine now with higher voice quality (HD audio) - **Improved** The "Enable encrypted telephony" option is offered for the provider "Drillisch GmbH" - **Improved** Order of telephone numbers in telephone book entries can be changed more easily - **Improved** The call list shows the country, or for domestic calls, the location, where the call originated ## DECT: - **NEW** The number of DECT telephone calls possible concurrently was increased from three to five ## DECT/FRITZ!Fon: - **Improved** Display of Wi-Fi account information can now be switched on or off for each FRITZ!Fon - **Improved** Easier deletion of multiple emails via the "delete multiple" option - **Improved** "Weather" start screen now available in all countries ## Home Network: - **NEW** Names can now also be assigned to devices that use the guest access - **NEW** Improved overview through individual icons for network devices - **Improved** Detailed settings of a device on the "Home Network > Network Connections" page redesigned - **Improved** Troubleshooting and settings for speeds on WAN/LAN connections reworked - **Improved** Random calculation of the Unique Local Address (ULA, IPv6) in accordance with RFC 4193) ## Smart Home: - **NEW** On the device page of FRITZ!DECT 350 window sensor in the FRITZ!Box user interface, window open detection can be configured for the selected radiator controls - **NEW** The templates also allow the user to set the target temperature for radiator controls; the brightness, saturation, and color for lights, and the position for roller shutters in percentage steps - **NEW** The temperature settings for the radiator control can be restricted to a lowest and highest temperature - **NEW** Routines can also be triggered by a preset time or a time relative to sunrise/sunset - **Improved** Reworked registration of Smart Home devices via the FRITZ!Box user interface ## System: - **NEW ** New diagram of the FRITZ!Box connection status in the overview (homepage) - **Improved** File name for saved settings now includes name of individual FRITZ!Box - **Improved** A personal subject line can be be specified for push service - **Improved** Reworked configuration of push service - **Improved** Communication to all AVM services for the FRITZ!Box (update, etc.) preferentially via IPv6 with fallback to IPv4 - **Improved** Link to reset the password more prominent in the "Forgot password" email - **Improved** With "Diagnostics > Function" the services for the Network Time Protocol are checked and relevant information displayed about any errors found - **Improved** Simplified address changes in push service through the new default recipient, which can be specified independently of the sender - **Improved** Changes to sender information for email from push service require additional confirmation - **Improved** Shorter interval for sending push service emails with notifications on user logins with the FRITZ!Box - **Improved** "Transfer Your Settings to a New FRITZ!Box" wizard improved for a smoother switch from DSL to fiber optic or cable - **Improved** More reliable detection of FRITZ!Box updates already performed through use of the "Transfer Your Settings to a New FRITZ!Box" function ## USB/Media Server: - **Improved** Energy-saving function now also works with USB storage devices in Green Mode (USB 2.0) - **Improved** Data packets downloaded from fritz.nas now include the name of the given FRITZ!Box model and a time stamp in the file name to ease identification ## Powerline: - **NEW ** Password for all devices in the powerline network can be changed with a single click # Additional Improvements in FRITZ!OS 8.00 ## Internet: - Changed:- The AES-192 encryption algorithm is no longer supported in Phase 2 SAs of VPN connections - **Changed** The hash algorithm MD5 and the 3DES encryption algorithm are no longer used on VPN connections over IPSec for reasons of security - **Changed** The IPv6 option "Assign unique local addresses (ULA) as long as no IPv6 internet connection exists (recommended)" is no longer offered - **Changed** In PPPoE passthrough operation of the FRITZ!Box, DNS root queries are no longer filtered via UDP - **Fixed** Under some circumstances the network traffic of a connected telephone system was not routed via a specially configured VoIP interface - **Fixed** Under certain circumstances, OpenWrt devices operated behind a FRITZ!Box did not receive an IPv6 connection to the internet - **Fixed** Independent port sharing (UPnP) for the same port with various home network devices did not work under certain circumstances - **Fixed** In some circumstances active WireGuardŽ connections were interrupted when adding or deleting WireGuardŽ connections - **Fixed** VPN connections via WireGuardŽ to an endpoint given as multiple (comma separated) domains could not be established ## Wi-Fi: - **Changed** For improved compatibility with older wireless devices, security settings can be adjusted on the "Wi-Fi > Security" page - **Changed** Text reference to selection of "WPA2 + WPA3" Wi-Fi encryption removed - **Fixed** Display of Wi-Fi properties of a registered wireless device was in rare cases incorrect - **Fixed** When 5-GHz channels were checked for radar (DFS), no wait cursor was displayed under these channels in the user interface - **Fixed** Repeaters that were logged into the guest network were not marked as "Wi-Fi guests" ## Home Network: - **Changed** Recommendation to enable the automatic update search at the bottom of the Mesh Overview page ## System: - **Changed** The link generated by "Forgot Password" push service in the email is valid for 20 minutes - **Fixed** After results of functional diagnostics were sent, an event message about changed FRITZ!Box settings was displayed - **Fixed** The "Live TV" button for Magenta TV streaming was missing in the user interface when displayed on smartphones and tablets ## USB/Media Server: - **Fixed** Files in a folder on the highest level of a file tree could not be moved, copied, or deleted via FTP - **Fixed** In certain constellations, access to NAS contents via download link was not possible --- # New functions of FRITZ!OS 7.81 ## DSL: - **Fixed** Establishing a VDSL connection with some specific DSL lines sporadically took very long or was repeatedly disrupted ## Internet: - **Fixed** During active VPN connection over WireGuardŽ with transmission of entire network traffic, the FRITZ!Box allowed selection of user for HTTPS access - **Fixed** In certain browser versions https pages were not filtered reliably - **Fixed** Incorrect entry for the NTP server in DHCPv6 reply of the FRITZ!Box resulted in IPv6 home network devices not being able to obtain a valid time ## Telephony: - **Fixed** Telekom CompanyFlex SIP trunking - Outgoing calls failed when telephone number suppressed - **Fixed** Under certain conditions, voice transmission was disrupted after a short time during ongoing telephone calls - **Improved** The list of voice codecs for telephony was reworked for the provider Telekom ## Smart Home: - **Fixed** Devices that were registered with the FRITZ!Smart Gateway were not displayed on the user interface of the connected FRITZ!Box - **Fixed** Link for automatic adjustment between an external temperature sensor and a radiator control was lost when the FRITZ!Box restarted - **Fixed** Status of the FRITZ!DECT 350 was transmitted incorrectly in the Smart Home home network - **Fixed** The freely selectable device name for FRITZ!DECT 350 was not adopted - **Fixed** Under certain circumstances empty Smart Home pages were displayed in the FRITZ!Box user interface ## System: - **Fixed** After failed download of a FRITZ!OS update, under certain circumstances no further update queries - **Fixed** When using the "Transfer Your Settings to a New FRITZ!Box" wizard, a successfully established internet connection via DOCSIS was sporadically not detected and an incorrect error page was then displayed - **Fixed** When using the "Transfer Your Settings to a New FRITZ!Box" wizard, a backup of the FRITZ!Box internal memory unnecessarily included files that were saved on an external USB storage device connected to the FRITZ!Box - **Fixed** When using the "Transfer Your Settings to a New FRITZ!Box" wizard, an error occurred if an IPv4 address range other than the preset range was used in the home network - **Fixed** When using the "Transfer Your Settings to a New FRITZ!Box" wizard, the IP filter list was not transferred to the new FRITZ!Box - **Fixed** When using the "Transfer Your Settings to a New FRITZ!Box" wizard, the settings for DNS rebind protection were not transferred to the new FRITZ!Box - **Fixed** When using the "Transfer Your Settings to a New FRITZ!Box" wizard, the "Factory settings" status of the new FRITZ!Box was not always reliably detected and it was not possible to transfer the settings - **Improved** When using the "Transfer Your Settings to a New FRITZ!Box" wizard, the settings for the captive portal of a public Wi-Fi hotspot are now transferred to the new FRITZ!Box --- # New functions of FRITZ!OS 7.80 ## Internet: - **NEW** Simplified configuration for connection to a fiber optic modem (ONT) - **NEW** The speed of the Ethernet connection between LAN 1/WAN and the upstream device (e.g., fiber optic modem) is displayed on the overview page # Further Improvements of FRITZ!OS ## DSL: - **Improved** Reworked DSL overview for FRITZ!Box - **Improved** ADSL2 interoperability problem let to connection disruptions for some remote sites ## Internet: - **Fixed** IPv6 sharing settings as "Exposed Host" for devices with delegated IPv6 prefix were sporadically deleted - **Fixed** Problem with DNSSEC validation in FRITZ!OS - **Fixed** When an internet connection was reestablished, occasionally an outdated IPv6 prefix was not deleted on a downstream router - **Improved** Increased robustness of time determination (NTP) - **Improved** New provider "Odido" can be selected for the Netherlands - **Improved** Preset upstream and downstream values adjusted for internet connection on an external modem ## Wi-Fi: - **Fixed** Connection problems with the Nuki Smart Lock - **Improved** Problematic situations during operation of VR headsets Meta Quest 2/3 improved ## Telephony: - **Fixed** During an active parallel call, after a brief period the call was signaled only at the call destination - **Fixed** Termination of outgoing calls to certain mobile sites after two minutes - **Improved** Telephony more stable ## DECT/FRITZ!Fon: - **Change** Presets for the Deutschlandfunk web radio stations were updated ## System: - **Improved** Stability --- # New functions of FRITZ!OS 7.55 ## System: - **NEW** In the new energy-saving mode, Wi-Fi, LAN and USB use even less power - **NEW** New wizard transfers all important Internet, telephony, and WLAN settings as well as connections to mesh, telephony, and smart home devices to a new FRITZ!Box --- # New Features in FRITZ!OS 7.50 ## Internet: **NEW** Automatic prioritization provides for fairly distributed data rates throughout the entire FRITZ!Box network (home network and guest network) **NEW** VPN with WireGuard for simple setup of fast, secure VPN connections **NEW** The MyFRITZ! direct connection allows you to receive information on the FRITZ!Box in real time on MyFRITZ!Net. ## Wi-Fi: **NEW - Supports continuous availability of 5-GHz Wi-Fi with radar detection ("Zero-Wait-DFS") ## Telephony: **NEW** Call handling allows call blocks and call diversion (e.g. to answering machine) for callers "not in the telephone book" (telephone book as positive list) **NEW** On a SIP DDI line for corporate customers, call diversion settings can be configured so that the caller number is displayed at the destination (partial rerouting) ## DECT/FRITZ!Fon: **NEW** The new, optional "Voice" ringtone announces the name in the telephone book that matches the caller number, or the location and the telephone number. For an alarm or appointment, the ringtone announces the reason for the reminder **NEW** The new FRITZ!Fon convenience function "Appointment Calendar" rings to remind about appointments **NEW** Handset can display WiFi password, also QR Code for convenience, Can be protected by PIN code ## Smart Home: **NEW** Configure and apply scenes to generate the mood for any occasion **NEW** Create and enable or disable routines (if-then combinations) for automatic interactions in the Smart Home **NEW Templates for the comfort functions switch Wi-Fi access, switch Wi-Fi guest access, start telephone call, switch answering machine, send email (push service), and open web service (URL) **NEW** Selection of an additional display of the temperature and humidity profile on the FRITZ!DECT 440 **NEW** Natural lighting sequences for device groups and templates with FRITZ!DECT 500 **NEW** Support for compatible external window sensors for the radiator controls' open window detection ## USB: **NEW** Support for storage media formatted in exFAT ## System: **NEW** "Help and Info" in the user interface: A completely overhauled help function with many instructions based on user scenarios and a strong search engine ## FRITZ!Apps: **NEW** MyFRITZ!App offers the option to enable prioritization for internet access on each home network device **NEW** MyFRITZ!App allows home network devices to be renamed **NEW** MyFRITZ!App allows a MyFRITZ! account to be created for MyFRITZ! internet access to the user interface of the FRITZ!Box (for iOS) **NEW** FRITZ!App Smart Home supports scenes and the enabling and disabling of routines **NEW** FRITZ!App TV allows the TV function (DVB-C) and station search to be enabled for FRITZ!Box Cable devices ------------------------------------------------------------ # Further Improvements of FRITZ!OS 7.57 ## System: - **Fixed** stability and security increased # Further Improvements of FRITZ!OS 7.56 ## System: - **Fixed** "Transfer your settings to a new FRITZ!Box" was not visible in fritz.box / Wizards # Further Improvements of FRITZ!OS 7.55 ## Internet: - **Improved** Clarified wording when configuring WireGuard VPN connections - **Improved** NTP interoperability improved through better estimation of the hardware clock's deviation - **Improved** Optimization of bandwidth reservation in the home network through adjustment to transmitted downstream rate - **Improved** Optimized switching from public DSN servers to provider-side DNS servers - **Improved** The setting to send all IPv4 data traffic of the FRITZ!Box via the WireGuard VPN connection to (!) a single device is no longer supported - **Fixed** "Reserve bandwidth in the home network" did not work with IPv6 - **Fixed** During preparation of the first WireGuard connection via remote dial-in the FRITZ!Box ended up in permanent wait mode - **Fixed** In certain scenarios, switching the type of internet connection led to the WAN interface being switched to LAN - **Fixed** Interoperability of IPSec VPN connections to LANCOM remote sites including usage of VNC and RDP with active packet acceleration not available - **Fixed** MyFRITZ! access permission (device sharing) could sometimes only be terminated via IPv4 - **Fixed** Occasionally an IPv6 prefix sharing of a previous "outdated" prefix for a downstream router was not deleted - **Fixed** On DS Lite connections, switching off IPv6 manually (incorrect configuration) could result in repeated dial-in attempts by the FRITZ!Box - **Fixed** On TIM connections (Telecom Italia), configuration of a WireGuard connection led to repeated clearing of the internet connection - **Fixed** Parental controls: Tickets for devices with the standard profile could not be redeemed - **Fixed** Problems with functionality and/or display of the parental controls in certain application scenarios - **Fixed** Repeaters sometimes used external NTP servers for initial time determination even if the upstreamFRITZ!Box offered an NTP server - **Fixed** Under certain circumstances a switch to public DNS servers occurred although the current DNS server could be reached - **Fixed** Under certain circumstances a switch to public DNS servers took place too early - **Fixed** VPN: When configuring an IPSec-LAN-LAN connection, the address of the FRITZ!Box was not proposed - **Fixed** When all IPv4 data traffic was routed over a WireGuard VPN connection, incoming calls were not always signaled - **Fixed** When packet acceleration was enabled during longer LAN-LAN linkups to CISCO remote sites via IPSec, occasional connection losses occurred ## Wi-Fi: - **Fixed** Mesh Repeater operating mode: The "Select Wi-Fi Network" list did not display invalid Wi-Fi network names (SSID) ## Mesh: - **Fixed** After changing the connection of a repeater, the connection display on the "Home Network > Mesh" page of the user interface was wrong - **Fixed** When using certain powerline adapters together with a network switch, the connection display on the "Home Network > Mesh" page of the user interface was wrong ## Telephony: - **Improved** Robuster handling of inconsistent data in Apple telephone contacts - **Improved** Support for using up to 10 individual telephone numbers (MSNs) with the "Telekom CompanyFlex" rate - **Change** Outdated entries removed from the list of telephone providers ## DECT: - **Improved** Support for DECT headsets from the Sennheiser EPOS series for outgoing calls and picking up calls via the headset button ## Home Network: - **Fixed** Devices with a dot in their name could no longer be renamed - **Fixed** Display for search for updates for devices in the Mesh was not suitable in certain cases - **Fixed** Possibly lacking rendering of IP addresses could cause subsequent defects ## System: - **Fixed** "Change notice" push service sent too often information on supposedly new port sharing - **Fixed** Repeater events were occasionally listed twice in the Event Log - **Fixed** There were too many events on changed settings in the Event Log ## Mobile Network: - **Improved** Internet connection with username/password supported for Alcatel IK41VE1 IoT/M2M 4G (MBIM) mobile network dongle ## USB: - **Fixed** No network drive function (SMB) could be established to Rclone - **Fixed** WebDAV online storage could not be used when the country was set to "Spain" ------------------------------------------------------------ # Additional improvements in FRITZ!OS 07.50 ## DSL: **Improved** Higher connection quality and stability to multiple remote sites **Improved** Adjusted calculation of available bandwidth in the user interface ## Internet: **Improved** When the DNS server of the internet provider (or the listed DNS server) is interrupted, automatic switch to the public DNS server **Improved** Failure detection via DNS validation added for "Expanded failover protection" **Improved** FRITZ!Box services (SMT, FTP, IGD and TR-064) offered via Bonjour or mDNS **Improved** Unwanted queries from certain IP addresses to FRITZ!Box services can be blocked with the new IP block list **Improved** "QUIC" added to the internet protocols supported by parental controls **Improved** When internet access to storage media via FTP/FTPS is enabled, the randomly preselected port number is displayed **Improved** Support for VPN user dial-in for Android mobile telephones and tablets with IKEv2 IPSec (preshared key) **Improved** Optimized upload and download speeds by adjusting the TCP segment size (MSS clamping), now also for IPv6-based connections **Improved** IPv4 VPN connections (IPSec) can be tunneled via IPv6, for instance to reach FRITZ!Box devices on DS Lite connections (IP6 tunnel for IPv4, IPv4-inIPv6) **Improved** In the user interface, an image now illustrates the different types of VPN connections **Improved** No publication of IPv4 address to MyFRITZ!Net on dual-stack connections with carrier-grade NAT; MyFRITZ! address always resolved here into the IPv6 address **Improved** After a restart, the FRITZ!Box refreshes its IP address with MyFRITZ!Net immediately (DynDNS update) **Improved** A FRITZ!Box in "Mesh Repeater" mode is automatically registered with the MyFRITZ! account of the Mesh Master **Improved** IPv6 on the FRITZ!Box enabled by default for all internet connections **Improved** FRITZ!Box can be operated on IPv6-only connections **Improved** Support for IPv6 during prioritization of network applications and prioritization of a home network device **Improved** The IPv6 Interface Identifier used on the WAN port is chosen at random **Improved** Improved tips and error messages on sharing ports on DSL Lite connections with PCP support **Improved** Data traffic from Wi-Fi calling (VoWifi) with smartphones prioritized over the FRITZ!Box internet connection **Change** Predefined selection of DynDNS providers replaced by a general settings option **Change** The "IPv6" tab is displayed for IPv6-only connections **Change** Support for the User Service Platform specification (USP, Broadband Forum TR-369) and configuration on the "Provider Services" tab **Change** When a new port sharing setting is created, the outdated "eMule" application is no longer listed **Change** Outdated entries removed from the provider list for internet access **Fixed** The ICMP identifier for pings was set to 0 by the FRITZ!Box in some rare cases **Fixed** The FRITZ!Box could send an invalid Phase1 ID for VPN user dial-in via IPSec **Fixed** The entry field for the IPv6 LAN prefix was too small **Fixed** The IPv6 address could not be entered manually for IPv6 port sharing **Fixed** Devices in the guest network with a captive portal were not connected to the internet via IPv6 **Fixed** IPv6: When SLAAC was used and the DHCPv6 server was disabled in the FRITZ!Box, after a restart IPv6 could not longer be used in the home network **Fixed** In individual cases, deletion of a port sharing setting deleted additional port sharing settings of the same device **Fixed** VPN connections (IPSec) to StrongSWAN via IPv6 failed under some circumstance **Fixed** VPN connections (LAN-LAN) could not be saved without a name **Fixed** In some scenarios the FRITZ!Box's NTP server did not work after re-establishing the internet connection **Fixed** Under certain circumstances, not all DNS servers made available by the provider were used ## Wi-Fi: **Improved** When a radar event is detected, the system attempts to hold the channel with reduced bandwidth **Improved** When encryption on the Mesh Master is changed to "non-encrypted", activation of the 5-GHz Wi-Fi network is ensured and wireless devices are correctly deregistered if necessary **Improved** Data rates increased when exchanging data with certain wireless devices **Improved** The legend below the "Allocation of Wi-Fi Channels" diagram on the "Wi-Fi / Wi-Fi Channels" page is now displayed in a single line **Improved** Optimized automatic channel selection when checking for prioritized use in the 5-GHz Wi-Fi network **Improved** The adjustment of radio channel settings in the 5-GHz frequency band now allows all channel numbers to be selected **Improved** The overlay with message on the "Load on the Current Wi-Fi Channel" diagram is now also shown when VHT160 mode is enabled **Change** New message under "System / Event Log" when a new session key was negotiated (encrypted connections compliant with the WPA3/SAE standard) **Change** Restructuring of the "Wi-Fi > Wi-Fi Network", "Wi-Fi > Security", and "Wi-Fi > Wi-Fi Channel" pages **Change** MAC address filters are limited to a maximum of 128 entries **Change** New message under "System > Event Log" when the maximum permissible number of repeaters is exceeded **Fixed** On the user interface for the "Wi-Fi Guest Access", starting the WPS quick connection was linked with the "Wi-Fi / Security / WPS" page **Fixed** Incorrect information when Wi-Fi disabled when "Internet connection via Wi-Fi" is selected **Fixed** The period for displaying the load on the Wi-Fi channel could not be changed in the user interface when the 2.4-GHz Wi-Fi network was disabled **Fixed** Sorting of "Other Wi-Fi Networks in Your Vicinity" table by name did not always work reliably ("Wi-Fi / Wi-Fi Channel" page) **Fixed** Preset name for Wi-Fi guest access linked to the language selection **Fixed** When a WPS quick connection was started during the check for higher-priority users (e.g. radar), an incorrect message could be displayed under "System / Events" ## Mesh: **Improved** Display of home network connections on the "Mesh" page of the user interface responds more quickly to changes **Improved** Home network devices (e.g. printers or NAS) displayed in the "Mesh Overview" can be opened directly by link **Improved** Changed country and language settings of the Mesh Master are automatically transmitted to the Mesh Repeater **Improved** New message in "System / Event Log" when FRITZ!OS removes a network loop **Improved** "Mesh Overview" now shows network switches that use the LLDP protocol **Improved** "Mesh Overview" now shows deployed network switches or access points in sequence **Improved** Indication on the start page of the user interface when there are FRITZ! devices in the home network that are not yet enabled for Mesh ## Telephony: **Improved** Online contacts from web.de, gmx.de, and 1&1 converted to CardDAV **Improved** Revised display of table of configured call diversions **Improved** Encrypted telephony more robust against lost connections **Improved** Optimization for integration of a telephone book into Mesh **Improved** Designation of a caller's telephone number in the call list, even when a telephone number specified by the caller was also transmitted **Improved** Optimization of automatic configuration of telephone numbers by the internet provider **Improved** Reworked texts for push services on fax function and answering machines on fax function and answering machine **Improved** Support for more call scenarios with voice data transmission before call acceptance (P-Early-Media) **Improved** Wizard for telephony devices enables configuration of internal fax function without enabling fax reception **Improved** Display of certain table columns in the "Telephone Numbers" can be switched on or off **Improved** CAPI over TCP can be disabled if desired via "Diagnostics / Security" **Improved** Prioritization of telephony data adjusted to comply with the Deutsche Telekom specification 1TR112 V14 **Improved** FRITZ!Box takes note of the last 20 destination telephone numbers for call diversion and offers these when new call diversion settings are configured **Improved** For messages on the answering machine, the name that matches the caller's number in the telephone book, or the location and telephone number, can be announced while listening to messages **Improved** Call diversion settings and call blocks for incoming calls can be restricted to a single telephone number in the home network **Improved** Supports groups for online contacts from Apple **Improved** Support for photos for online contacts from Apple, Telekom, and CardDAV providers **Change** Different designations in the user interface for telephones on the "FON 1" and "FON 2" jacks **Fixed** If the internal fax machine was used with the "only send" setting, incoming calls were not logged in the call list **Fixed** Newly created telephone numbers could not always be edited retroactively **Fixed** Root number was not displayed when the settings of the SIP DDI line were edited **Fixed** Umlauts in the names of telephony devices were sometimes converted into special characters **Fixed** Under certain rare conditions, the initiator of a three-party conference was not able to hear the two other parties ## DECT/FRITZ!Fon: **Improved** Higher resolution of images from Google online contacts **Improved** Convenient control of DECT headsets that are GAP or CAT-iq 2.x-compliant **Improved** Quick dial for number keys 2 to 9 can be set up directly on the FRITZ!Fon by pressing and holding the numbers **Improved** More convenient use of DECT handsets **Improved** Three new ringtones with bird sounds available for FRITZ!Fon ("Whistling", "In the Woods" and "Yardbirds") (configured under "MENU / Settings / Audio / Ringtone / Own ringtone") **Change** Missed calls older than 28 days are no longer signaled by a message key blinking red on the FRITZ!Fon ## Home Network: **Improved** Reworked details pages for network devices **Improved** FRITZ!Powerline devices can be restarted in the "Device Details" of the FRITZ!Box user interface under "Home Network / Network" or registered by clicking a button **Improved** Own network device highlighted in the overviews of the user interface **Improved** More flexibility when assigning your own names for a network device in the home network for display in the user interface: Spaces and special characters are allowed **Improved** The symbol in the user interface for prioritized network devices was updated **Improved** Reworked user guidance through changing of the FRITZ!Box name ## Smart Home: **Improved** Template for radiator controls expanded with addition of comfort temperature and cool-down temperature as well as antifreeze and boost functions **Improved** Sunrise/sunset schedule with more settings options independent of sunrise and sunset **Improved** The "Adaptive heating start" function can be disabled for radiator controls **Change** "Smart Home" menu subdivided into "Devices & Groups", "Automation" and "Operation" ## USB: **Improved** Media data are read in completely with "Refresh index" **Improved** A list of FRITZ!Box users with the right to access NAS contents is displayed under "Home Network Sharing" **Improved** A message appears indicating when the maximum number of sharing links is exceeded **Improved** After completion of fax configuration, a USB folder for storing faxes can be selected under "Settings for the Fax Function" **Change** When uploading files to fritz.nas, the creation date of the respective file is now displayed **Change** MagentaCloud removed as a media source in the internet because API is no longer compatible **Change** After indexing, the ".start_indexation.mp3" file is no longer displayed via SMT/FTP **Fixed** Added radio stations were displayed only after manual indexing **Fixed** After starting operation of "FRITZ!Box as Mesh Repeater", the network drive function (SMB) was not always available **Fixed** Accessing a sharing link allowed the creation of additional sharing settings **Fixed** During the slide show of FRITZ!NAS images, the control for the duration of the display was not displayed correctly **Fixed** Folders in the uppermost level of the directory structure were not displayed in the selection dialog for moving files ## System: **Improved** New display of Wi-Fi connections between FRITZ! devices **Improved** Summary of information areas on the "Overview" page for better orientation **Improved** New design and improved operation concept for logging in to the FRITZ!Box user interface **Improved** Revised layout of the FRITZ!Box user interface **Improved** Changed operating concept for changing settings in the user interface **Improved** Under "System / FRITZ!Box Users / Apps", the FRITZ!Box user from which each app has been configured is displayed for each app **Improved** The "Forgot Password" push service email now contains information on the device that requested this mail **Improved** If desired, the selection list of FRITZ!Box users can be hidden during login to the user interface from the home network **Change** Simplified flashing behavior of the FRITZ!Box LEDs when connection is triggered by the "Connect" button **Change** The hyperlinks for Contents, Manual, Tips & Tricks, en.avm.de, and Legal Notice are now located under "Help and Info" **Change** New contents under "Help and Info / Get to Know the Functions" **Change** Additional confirmation for configuring certain settings can no longer be switched off **Change** The push service for the Wi-Fi guest access sends registration and deregistration events of the guest devices from the Mesh Repeater or Mesh Master with which the devices are registered **Fixed** The display of several "Exposed Hosts" for two different devices under "Diagnostics / Security" was sometimes misleading ## Security: **Improved** Use of a random SIP port possible under "Telephony / Telephone Numbers / Line Settings / Security" **Improved** All a user's rights listed under "System / FRITZ!Box Users" **Improved** Information about security methods currently used on SIP remote sites under "Diagnostics / Security / Telephony" **Improved** Display of the last ACS connections under "Diagnostics / Security / Provider Services (TR069)" **Improved** While login is blocked due to an incorrect password entry, the password entry field can be edited for the next login attempt **Improved** SIP port can be reached from the internet only by the set protocol (IPv4 or IPv6) **Improved** Protection from frequent login attempts with incorrect password via the SMB protocol ## FRITZ!Apps: **Improved** FRITZ!Apps support with explanation of where the preset FRITZ!Box password is found on the FRITZ!Box **Improved** MyFRITZ!App shows when internet access is blocked for each home network device **Improved** MyFRITZ!App with additional connection information for the home network devices **Improved** When MyFRITZ!App is registered with a FRITZ!Box that has not yet been configured, MyFRITZ!App indicates this and offers to open the browser for configuration **Improved** MyFRITZ!App displays Wi-Fi dual-band connections for "Your Mesh" in the overview diagram **Improved** MyFRITZ!App reliably displays Mesh connection paths graphically, even for more complex constellations **Improved** MyFRITZ!App indicates when Mesh functions have not been enabled in the Mesh Repeater **Improved** MyFRITZ!App sets the name of the smartphone or tablet as the name of the network device in the home network of the FRITZ!Box if no name was assigned yet (for Android) **Improved** MyFRITZ!App supports the convenience function of call diversion for callers "not in the telephone book" **Improved** FRITZ!App WLAN displays the channel bandwidth of the Wi-Fi connection **Improved** FRITZ!App Smart Home displays the adaptive heating (preheating phase) of radiator controls **Improved** FRITZ!App Smart Home displays open window detection with a window sensor on the radiator control **Improved** FRITZ!App Smart Home supports the creation of templates for the current light setting **Improved** FRITZ!App Smart Home displays a message when applying templates ----------------------------------------------------------- [1] Talking caller ID - FRITZ!Fon learns to speak: New features for FRITZ!Fon New "Voice" Ringtone The new "Voice" ringtone announces the name of the caller, if available, or the location the call is coming from along with the telephone number of the caller. The feature is available for incoming calls, but a voice announcement can also be selected for alarms and appointments. When you get a call, instead of a ringtone the caller's name is announced if their telephone number is in your contacts. If there is no telephone book entry, the location from which the call is coming is announced, depending on the country, along with the telephone number of the caller. You'll need to have an active MyFRITZ! account. This feature can be enabled under "Telephony / Telephony Devices" in the user interface. Select the FRITZ!Fon handset you want to edit, assign one or more telephone numbers for incoming calls, and then switch to "Ringtones". Select there the "Voice" ringtone for the corresponding telephone number at the end of the list. You can configure additional settings under "Voice Ringtone". For alarms and the appointment calendar you can select the "Voice" ringtone directly on the FRITZ!Fon. Appointment Calendar With the new calendar, you can now set up appointments in FRITZ!Fon and create a reminder for them. You can also be reminded of the appointment with the new "Voice" ringtone. Note: The new features are available for FRITZ!Fon M2, C4, C5 and C6 with the latest handset firmware. ------------------------------------------------------------ [2] WireGuard Support for Simple Setup of VPN Connections WireGuard(R) is a modern, easy to understand, fast, and simple VPN solution. For most operating systems, there are apps or programs from WireGuard for connecting single devices to a network via WireGuard VPN. WireGuard is a registered trademark of Jason A. Donenfeld (https://www.wireguard.com). WireGuard is not compatible with other VPN protocols. Therefore it cannot connect to IPSec, OpenVPN and similar peers. WireGuard itself does not contain any mechanisms for key distribution. Both parties therefore require the public keys of the respective remote site. The concept for the FRITZ!Box is that both key pairs can be generated on the FRITZ!Box to set up a connection, and all the necessary dial-in data can be imported on the client side via a file or QR code, e.g. in the WireGuard App. For your FRITZ!Box to be accessible via WireGuard VPN, you need a MyFRITZ! address your (you'll need to register your FRITZ!Box with MyFRITZ!Net) ? or a third-party DynDNS address for your FRITZ!Box. Please note that the connection configuration ? QR code or configuration file - is not permanently stored on the FRITZ!Box (for security reasons). Do not let the QR code or configuration file fall into the hands of unauthorized persons. ------------------------------------------------------------ [4] More Operating Convenience in the FRITZ!Box User Interface The FRITZ!Box user interface has been visually refreshed with the new version. Particularly noticeable here is the separation of the menu from the left edge of the screen and the width of the displayed pages have been trimmed for better readability. This has a positive effect on tables and texts, especially when displayed on particularly large screens (resolutions), and at the same time improves the display on smartphones and tablets. The redesign is based on a new style guide that facilitates the integration of innovative operating concepts. ------------------------------------------------------------ [5] Automation Scenes - Create the Perfect Mood for Every Occasion With scenes you can simultaneously perform different actions in the Smart Home. For example, with the "Coming Home" scene, all radiator controls can be set to the comfort temperature at the touch of a button, and your LED lights and smart plugs, the Wi-Fi and/or guest Wi-Fi, and the answering machine can all be switched on at the same time. The preconfigured two scenes "Coming Home" and "Leaving Home" and can be applied directly. They consist of automatically generated templates that can be subsequently turned on and off as required. With a scene you create yourself, multiple devices can be combined and controlled. Templates that have already been created can be added and deleted on an individual basis. Furthermore, individual templates can be created as a simple scene. Settings for devices and/or device groups can be saved and reused with templates. Scenes can be used via the FRITZ!Box, a FRITZ!Fon, FRITZ!App Smart Home or the FRITZ!DECT 440. Routines - for Customizable Automations in the Smart Home Routines enable devices, scenes and templates to be automatically controlled or enabled by an if-then link. The shortcut consists of a trigger and a condition that must be met for an action to be performed. In the Configuration Wizard, you can define a device as a trigger, then specify the change in state or an event (condition). Finally, a previously created scene or template (action) is selected, which is activated when the condition is met. For example, if the humidity measured by the FRITZ!DECT 440 reaches a certain level, the previously configured scene "Ventilation" with a FRITZ!DECT 200 smart plug with a connected humidifier is applied. ------------------------------------------------------------ [6] Additional Confirmation After this update, additional confirmation for certain settings and functions can no longer be disabled. However, if additional confirmation was disabled before the update, this condition remains intact after the update. AVM recommends always using additional confirmation for reasons of security. To allow changes to protected settings from on the go, the TOTP standard with one-time passwords can be also used for additional confirmation. A freely available password manager or a separate app like the Google Authenticator can be used for this. ------------------------------------------------------------ # Additional improvements in FRITZ!OS 7.31 ## DSL: - **Improved** Upgraded stability and interoperability with Supervectoring (35b) - **Improved** Better stability and interoperability - **Improved** Stability and data rates with vectoring (17a) improved - **Improved** Stability to certain ADSL2+ remote sites improved # Additional improvements in FRITZ!OS 7.29 ## Internet: - **Improved** List of trusted certification authorities updated - **Improved** When internet access to storage media via FTP/FTPS is enabled, the randomly preselected port number is displayed ## Telephony: - **Fixed** Restricted availability by telephone when using telephony via IPv6 - **Improved** Encrypted telephony more robust against lost connections - **Improved** Enhanced interoperability for use of encrypted telephony ## USB: - **Improved** compatibility with MacOS 12.0 "Monterey" - **Improved** compatibility with several older devices (printers, scanners) # Further Improvements of FRITZ!OS 7.28 ## DSL: - **Improved** Better calculation of attainable throughput - **Improved** For supervectoring (VDSL2 35b profile), interoperability with certain remote sites improved in the send direction ## Wireless: - **Improved** Better stability - **Fixed** Difficulties with energy saving option Target Wake Time (TWT) - **Fixed** Wi-Fi did not work after changing the SSID during DFS wait time ## USB: - **Fixed** No network drive connection (SMB) was possible with macOS Big Sur Version 11.3 # Further Improvements of FRITZ!OS 7.27 ## DSL: - **Improved** stability of VDSL increased ## Internet: - **Improved** Deutsche Telekom: Automatic configuration of telephone numbers (EasySupport) for connection via WAN/LAN 1 with a fiber optic modem - **Fixed** VPN connections on the basis of third-party providers were sometimes interrupted after long connection times - **Fixed** Wireless devices in the home network could not always be accessed via VPN - **Fixed** possible reboot when changing from DSL to WAN connection mode ## Wireless: - **Improved** Better stability - **Improved** Interoperability with 11n Realtek chipsets - **Improved** Interoperability with 11b/g Chipsets (fragmented frames) - **Fixed** Possible problems while registering repeaters after changing Wi-Fir encryption from "WPA2+WPA3" to "non-encrypted" - **Fixed** WPS for the Wi-Fi Guest Access did not work reliably with non-encrypted Wi-Fi - **Fixed** The legend under the "Allocation of Wi-Fi Channels" diagram was not rendered in a single line ("Wi-Fi /Wi-Fi Channels" page)) - **Fixed** Vulnerabilities in the processing of incoming fragmented frames and aggregated MPDUs (A-MPDU) fixed ("Fragatttack") - **Fixed** IPv4 adress delivery with some devices hung - **Fixed** enabled chanel change on fixed chanel setup when disturbances are discovered ## Telephony: - **Change** Necessary change for use of a Google online telephone book in the future - **Fixed** After editing CompanyFlex Cloud PBX telephone numbers, these numbers were no longer registered - **Fixed** No display of call blocks if these included an entry without a telephone number - **Fixed** Searches in the telephone book could be performed using a name, but not a telephone number - **Fixed** Configuration of internal fax function not possible when a telephone book contained an entry without a telephone number - **Fixed** During use of encrypted telephony, if a caller cancels a call before it is picked up, telephones on the FRITZ!Box could ring endlessly - **Fixed** Occasionally, three-party conferences did not work on an analog telephones ## DECT: - **Fixed** After long operation times, certain functions were sometimes no longer available (e.g. media player, search for updates...) ## System: - **Change** Push Service: Various corrections to content of "Change notice" email - **Fixed** The code of the Google Authenticator could not always be entered on the user interface **Instructions for installing the update:** Use the update function offered in the user interface to install the update. This automatically offers you the right FRITZ!OS. Click "Wizards", select "Update" and then follow the instructions on the screen. --- (c) AVM GmbH 2004-2024. All rights reserved. This AVM firmware package contains files that are propagated under different licenses, in particular under a license held by AVM or under an open-source license (namely the GNU General Public License, GNU Lesser General Public License or FreeBSD License). For details on the various licenses, see the "license.txt" file (https://download.avm.de/fritzbox/license.txt). The source code of the files propagated as open source files can be obtained upon a written request to fritzbox_info@avm.de. AVM grants the non-exclusive right to use this AVM firmware package, which is supplied exclusively in object code format. The licensee may create only one copy of the software, which may be used exclusively for backup use. AVM reserves all rights that are not expressly granted to the licensee. Without previous approval in writing, and except for in cases permitted by law, it is particularly forbidden for this AVM firmware packet to be - copied, propagated, or in any other manner made publicly accessible, or - processed, disassembled, reverse engineered, translated, decompiled or in any other manner "opened" and subsequently copied, propagated or made publicly accessible in any other manner. SST 2024-09-12